W3vina.COM Free Wordpress Themes Joomla Templates Best Wordpress Themes Premium Wordpress Themes Top Best Wordpress Themes 2012

Tag Archive | "Lean"

Bear Cruzer Tuning, Centershot Off and Cam Lean #archery

Discount Prices on Archery Supplies Right Here

I recently purchased a Bear Cruzer RTH package from Cabela’s. I know it’s not a top of the line bow, but it’s replacing my Browning Ballistic Mirage that I’ve had for close to 12 years, so it feels like a pretty big upgrade to have something modern.

I am trying to get it tuned and running into some issues. I set the rest (whisker biscuit) at Centershot and I get a pretty bad right tear on paper. In order to get a bullet holes I have to push the rest pretty far from the riser, so much that the arrow is visually crooked when looking at the bow. Looking at the cams, the top Cam leans a little, if I lay an arrow on the cam, it intersects the string right at the d-loop. The bottom cam however is way worst. The bottom cam visually looks like it’s leaning, the string is slightly off center coming off the groove, and an arrow intersects a few inches before the loop when pressed against the cam. Both cams lean towards the cables, this was measured at brace.

I am assuming I need to yoke tune. I am hesitant though because I don’t want to screw up the timing of the dual cam system. Both cams are identical, I would think both cable lengths need to be identical. Can I yoke tune the bottom cam only, or do I need to do both cams?

I am shooting a 58 pound draw at 28 inches. My arrows are Easton carbons cut to 27.75 with 100gr tips. They are a 400 spine.

Any input would be appreciated.


ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat – General Archery Discussion

Discount Prices on Archery Supplies Right Here

CLICK HERE To Find The Lowest Price

Posted in Best archery reviewsComments Off on Bear Cruzer Tuning, Centershot Off and Cam Lean #archery

Cam lean question #archery

Discount Prices on Archery Supplies Right Here

Reading the nuts and bolts of archery and checking cam lean on my Reign 7. Thought I read about wanting the top cam/idler wheel at zero, line with straight edge on cam/idler parallel with string when at full draw on the board. What about the lower cam? I’m thinking you want the same. Is that correct? I’m sure it will get changed when final tuing but trying to start correct and fresh. Also will be changing threads and would like to know where to start when that’s done.


ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat – General Archery Discussion

Discount Prices on Archery Supplies Right Here

CLICK HERE To Find The Lowest Price

Posted in Best archery reviewsComments Off on Cam lean question #archery

Lower single cam lean?

Discount Prices on Archery Supplies Right Here

Has anybody ever had their lower cam (single cam) lean? I adjusted the yoke cable to fix the upper cam lean, but the lower cam is definitely leaning. I can tell that it is not level with the limbs, but do not know if it is the cam or the limbs.


ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat – General Archery Discussion

Discount Prices on Archery Supplies Right Here

CLICK HERE To Find The Lowest Price

Posted in Best archery reviewsComments Off on Lower single cam lean?

cam lean on my high country speed pro

Discount Prices on Archery Supplies Right Here

I have a problem with my bow that the top cam is rubbing into the string. I have a 2008 high country speed force. It seems like the came is leaning too much and the string is rubbing on the side of the cam. Here are some pics of it. Can anyone help me out with this diagnosis? The cam also looks like it is almost touching the limb.
Attached Images

ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat – General Archery Discussion

Discount Prices on Archery Supplies Right Here

CLICK HERE To Find The Lowest Price

Posted in Best archery reviewsComments Off on cam lean on my high country speed pro

cam lean

Discount Prices on Archery Supplies Right Here

i’m a little ocd about cam lean on bows. how do you remove cam lean from 2 track cam? yes it’s elite

ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat – Bow Tuning

Discount Prices on Archery Supplies Right Here

CLICK HERE To Find The Lowest Price

Posted in Archery tips & tricksComments Off on cam lean

Elite Answer cam Lean

Discount Prices on Archery Supplies Right Here

I have a new to me 2013 Answer and I’m treading into unknown waters with these types of cams.

At full draw the bottom cam leans like this \ pretty bad. The top cam is good

I’m going to order a shim kit but to save time and trouble, I need some info.

Which side, of the cam, do I need to shim in order to correct this amount of lean?

I have read and researched that I need zero lean at full draw. Is this correct?

If I have no lean at full draw then I should have a little lean at brace. Correct?

Thanks in advance.


ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat – Bow Tuning

Discount Prices on Archery Supplies Right Here

CLICK HERE To Find The Lowest Price

Posted in Archery tips & tricksComments Off on Elite Answer cam Lean

Heartland Archery | Winnipeg

Discount Prices on Archery Supplies on Amazon.com








Powered by WP Robot

1 or more persons associated with this website : http://archery-store.eshcarmel.org are participants in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for blogs and websites to earn advertising fees by advertising and linking to amazon.com -- Compensation Disclaimer : Some of the links on this site will earn a commission when a person makes a purchase through our links. Every effort has been made to remain fair, accurate, and unbiased. Also see our FTC Disclaimer page.